Remove front seat belt shoulder anchor bolts. Once the trim is free from the dash set it safely aside. The cd's dont eject, error 3 message, so im going to take the unit out to further investigate. Next you'll need to remove four 4 10mm black bolts to lift up the center console to get to the amplifier installed underneath. Remove 4 bolts under radio 10mm. Find 2 screws going upwards, 1 in each air vent, and remove them.
On all models, remove right and left No. Apply pressure until the clips disengage and work your way up the trim. Remove the 4 bolts, and the radio is out. Removing the glove box gets you nowhere. The radio has 4 10mm bolts or philips screws holding it in some bolts had a philips cut on them as well. Using screwdriver, pry and remove right and left rear trim covers and rear trim panel.
This pull would involve removing this parts. With these four bolts removed, grab the front of the center console section and lift up and back, the center console will pop apart from the front console skirt. Reinstall in the reverse order. The rest should be easy. On all models remove screws, disconnect connector and remove box. Gently pry both bottom corners of climate control face up then towards the rear until clear of lock.
Remove nuts and right and left cowl side trim panels. Look to see if there are any screws near the vent grilles, remove them, if they are there. Yes it really involves taking all those parts out just to get to the rotary switch. Slide the new stereo into the Toyota radio mounting kit, which is a thin metal cover and secure it per the manufacturer's instructions. Remove the screws from the front of the mounting brackets.
Unplug the antenna and the wiring harnesses. Reconnect the negative battery cable and turn the radio on. Connect the wires to the wires on your new stereo's harness. Remove cable attached to lighter socket. Remove the 4 bolts, and the radio is out.
Remove handle plugs, screws and all assist grip handles. I'll post pictures at www. These modern times find the heater unit fitted into the body before almost anything else and the complete dashboard and steering column assembly fitted over the top of it. Secure the radio in the dash with the original four screws and replace the trim. Grab the plastic bar between the heating vents and the stereo.
Cars designed to drive on the right side of the road which are effectively converted to drive on the wrong side of the road or vice-verso usually have any access effectively blocked off. The whole center fascia then pulls out towards you. To pull the plastic baffle off the dashboard: Adjust the heating vents so they point downwards. May want to wipe down the faces of all your gauges while you are at it. Yours should be one piece including the trim around the radio.
Using screwdriver, pry and remove right and left quarter trim hole cover or quarter trim upper belt hole cover if equipped with No. Once the screws are out, the bezel will pull straight off, unplug the wires then set aside. Locate a crescent wrench, a long extension if you have one, and a 10mm socket. You will not be able to see two philips screws just above the vents. Carefully push the unit out the front of the dash.
Find 2 air vents, one to either side of radio, and push the top of vent as if air would be directed upwards. Pull off the 3 knobs for the heat controls. Grab the center rib of the console tray the tray under the shifter and lift straight up. Vehicle: Toyota Sequoia Dash Cover Mat Pad - Fits 2001 - 2007. . Pull the head unit out of the Toyota highlander dash and disconnect the wires from the back of the radio. Our dash covers take in effect all air vents, sensors, airbags, dash trays and cup holders, and all other necessary functions on the dash dash speakers get covered as that is generally the first part of the dash that cracks due to heat, speaker sound penetrates through the dash as though it wasn't there.
Remove right and left front lower seat belt anchor bolts. Remove the ashtray and ashtray holder. Remove the instrument cluster and trim panel around the cluster. Plug the wiring harness adaptor and antenna wire into the back of the new stereo. Installing a new stereo in the Toyota Corolla gives improved sound and updated features. Look to see if there are any screws near the vent grilles, remove them, if they are there.